When EV Batteries Fail: Why Fires Become So Catastrophic — and How to Make Them Safer

Blurs.co.uk
16 Min Read
Summarize with AI

Electric vehicles are often described as carrying a huge amount of energy beneath the cabin. That is not just a dramatic way of putting it: a modern traction battery stores enough electrical energy to move a heavy vehicle for hundreds of miles. Under normal conditions, sophisticated electronics and physical protection keep that energy under control. But if a lithium-ion cell fails in the wrong way, the result can be a chain reaction that is exceptionally difficult to stop.

The phenomenon is known as thermal runaway. It helps explain why a relatively small fault inside one battery cell can, in rare cases, develop into a vehicle fire involving intense heat, flammable gases, toxic smoke and the possibility of reignition. Understanding the chemistry also points towards the most effective ways to make electric vehicles safer.

What actually happens inside a failing battery?

Most electric cars use lithium-ion battery cells. Each cell contains a positive electrode (cathode), a negative electrode (anode), a separator that keeps the electrodes apart, and an electrolyte that allows lithium ions to move between them. During charging and discharging, lithium ions travel through the cell while electrons flow through the external circuit.

The separator is crucial. It is designed to prevent the electrodes from touching while still allowing ions to pass. If it is damaged, melts, or is penetrated by a defect or foreign particle, an internal short circuit can form. A large current then flows through a tiny area, generating heat. That heat can trigger further chemical reactions inside the cell, which release still more heat.

Once heat is being generated faster than it can escape, the cell can enter thermal runaway. The electrolyte and other materials break down, pressure rises, and the cell may vent hot gases. Those gases can be flammable and toxic. If they ignite, flames can emerge forcefully from the pack. The cell can also release enough heat to push neighbouring cells into the same condition.

This is the critical difference between an ordinary electrical fault and a propagating battery failure: the battery contains both stored electrical energy and chemicals capable of sustaining an intense reaction. Cutting power to the motor does not remove the energy already stored inside damaged cells.

Why does one cell sometimes become a much larger fire?

A traction battery is made up of many individual cells grouped into modules and packs. The exact arrangement varies by vehicle. The pack is engineered to manage heat and electrical loads, but cells are physically close together because manufacturers are trying to package substantial energy into a limited space.

When one cell enters thermal runaway, heat can reach adjacent cells by conduction through the pack structure, by hot gases, and by radiation. If the cooling system and barriers cannot absorb or divert that heat quickly enough, the failure can spread from cell to cell. This is called thermal propagation.

Propagation is not inevitable. Pack design can delay or prevent it, and some cell chemistries are more thermally stable than others. But when propagation does occur, a fault that began in one small component can involve a large fraction of the battery.

The main triggers: damage, heat, electricity and defects

Mechanical damage is one important route to failure. A severe collision, crushing, road debris or penetration of the battery enclosure can deform cells or compromise their internal separators. Battery packs are protected by structural housings and crash-management systems, but no design can make a pack invulnerable to every impact. Damage may also be hidden: a vehicle can appear driveable after an incident while its battery has been compromised.

Excessive heat can also destabilise cells. This might follow exposure to an external fire, a cooling-system fault, or a localised hot spot. Battery-management systems monitor temperatures and can reduce power or shut down charging, but sensors cannot measure every point inside every cell.

Electrical abuse includes overcharging, excessive current, external short circuits and faults in control equipment. Battery-management systems are designed to keep cells within safe voltage, current and temperature limits. Their effectiveness depends on sound hardware, accurate sensing, robust software and fail-safe behaviour when a component or sensor goes wrong.

Manufacturing defects and ageing matter too. Contamination, damaged separators, inconsistent materials or tiny production flaws can create weaknesses that are difficult to detect. Over time, repeated charging cycles, high temperatures and other stresses can degrade cells. Age alone does not mean a battery is unsafe, but degradation and damage need to be monitored rather than assumed away.

These causes can overlap. A cell with a manufacturing weakness may survive normal use but fail after a minor impact or period of overheating. That is why safety cannot depend on a single protective device or one laboratory test.

Why are battery fires so difficult to extinguish?

In a conventional vehicle fire, extinguishing the visible flames and removing the fuel source can bring the incident under control. A battery undergoing thermal runaway is more complicated. The reaction is occurring inside the cells, and heat from one cell can continue to trigger others. Water is valuable because it cools the battery and surrounding materials, helping to slow propagation, but it may take sustained cooling to bring the pack under control.

Battery failure can release a mixture of gases, including flammable compounds and substances hazardous to breathe. If gases collect in an enclosed or semi-enclosed space, they can create additional fire or explosion risks. A damaged pack can also remain hazardous after visible flames have gone out. Reignition hours later is a recognised concern for emergency responders and vehicle recovery operators.

The UK government’s guidance for recovery operators warns that a vehicle may remain at risk even when obvious signs are absent. It advises trained personnel to look for warning signs such as gas release, unusual noises, chemical smells or rising battery temperatures, and to involve the fire service when a thermal event is suspected. These are not do-it-yourself inspection instructions: a damaged high-voltage battery should be left to appropriately trained professionals.

Are electric cars more likely to catch fire?

It is important to separate two questions: how often a vehicle catches fire, and how difficult a particular fire is to manage. A battery fire can be unusually demanding once it begins, but that does not mean electric cars are inherently more likely to catch fire than petrol or diesel vehicles. Comparisons depend on the dataset, vehicle age, mileage, fleet composition and what counts as a fire. Headlines that compare raw incident totals without accounting for the number of vehicles or distance travelled can be misleading.

The UK’s government guidance for recovery operators states that, based on the statistics available to it, the likelihood of an EV fire is low and a fire involving the battery pack is rarer still, while emphasising that the consequences can be serious. The sensible conclusion is neither complacency nor panic: the event is uncommon, but the potential severity justifies strong engineering standards, clear emergency procedures and transparent reporting.

What would make EV batteries safer?

1. Stop propagation, not just ignition. Preventing every possible cell fault may be unrealistic. A more robust design assumes that a cell could fail and makes sure the failure cannot easily spread. Better thermal barriers, cell spacing, directed vent paths, heat-resistant materials and module-level isolation can buy time or contain an event. Manufacturers should demonstrate, through demanding tests, that a single-cell failure does not turn into an uncontrolled pack-wide event.

2. Improve early detection. Battery-management systems should combine voltage and temperature monitoring with more sophisticated detection of abnormal pressure, gas release, impedance changes and unusual temperature patterns where practical. Software should recognise sensor faults and unexpected behaviour, alert drivers clearly, and move the vehicle into a safe state. Early warning is useful only if it is reliable and gives occupants enough time to leave safely.

3. Make packs tougher and easier to assess after a crash. Underbody protection, carefully designed crumple structures and impact-resistant enclosures can reduce the chance of cells being crushed or punctured. After a collision, vehicles should be able to report battery isolation status and detected faults to repairers and emergency responders. Clear criteria are needed for when a pack must be quarantined, inspected or replaced rather than returned to service on the basis of a superficial visual check.

4. Use safer cell chemistry where it makes sense. Lithium iron phosphate (LFP) cells generally offer greater thermal stability than some nickel-rich chemistries, although they have trade-offs in energy density, mass and performance. Choosing a chemistry is not a simple contest in which one option is universally best. Vehicle design, intended use, manufacturing quality and pack-level protection all matter. Research into solid-state batteries and less flammable electrolytes is promising, but new technologies must be independently tested at cell, module and full-pack scale before safety claims are accepted.

5. Raise the bar for manufacturing quality. Factories need rigorous contamination control, process monitoring, traceability and sampling that can identify defects before cells enter vehicles. Regulators should have access to meaningful production and failure data, not just a certificate based on a limited test programme. When a defect is found, recall notices should identify affected battery batches and explain what owners and repairers need to do.

6. Test realistic failure scenarios. Safety testing should include internal short circuits, crush and penetration damage, overcharging, exposure to external fire, ageing, manufacturing variation and failures of cooling or control systems. Tests should measure whether heat and flames propagate, how gases are vented, whether occupants can escape, and whether the pack can reignite after the initial event. A pass in a single controlled test should not be treated as proof against every real-world failure mode.

7. Design for firefighters, recovery crews and repairers. Emergency responders need vehicle-specific information showing battery locations, safe isolation points, high-voltage cable routes and appropriate tactics. Damaged vehicles need safe storage and monitoring arrangements, with clear handover procedures between fire services, recovery operators, insurers and repair facilities. Training and access to accurate manufacturer guidance are as important as the vehicle’s engineering.

Could a different battery technology solve the problem?

There is considerable interest in solid-state batteries, which aim to replace the conventional liquid electrolyte with a solid material. Some designs could reduce flammability and improve energy density. But “solid-state” is not a guarantee of zero fire risk: interfaces, manufacturing defects, short circuits and the behaviour of the complete pack still need to be understood. The technology must prove its safety and durability in mass production, not simply in a laboratory demonstration.

For more on that developing technology, see our investigation Solid-State Batteries: The Breakthrough That Could Change Electric Vehicles. The wider material supply chain matters too: our article Lithium: The Metal Powering the Modern World — And the Environmental Cost of Getting It looks at the resources behind battery production, while Cobalt Mining: The Human and Environmental Cost of a Critical Metal examines another important battery material.

What should drivers do if a battery may be damaged?

If an electric vehicle has been involved in a significant collision, suffered underbody damage, been exposed to flooding or shows unusual heat, smoke, hissing, popping or chemical smells, occupants should move away and contact the emergency services if a fire or battery fault is suspected. Do not touch exposed high-voltage components, attempt to open the pack, or try to tackle a suspected traction-battery fire yourself. Follow the vehicle manufacturer’s emergency advice and the instructions of the fire service. A vehicle that appears to have cooled down may still require specialist assessment.

The real safety test is what happens when something goes wrong

Lithium-ion batteries have made practical electric cars possible, and millions of vehicles operate without a battery fire. Their high energy density is also the source of the engineering challenge: when a cell is badly compromised, the stored energy and the chemistry can combine in a fast-moving event that is difficult to control.

The answer is not to abandon electric vehicles, nor to dismiss serious incidents as freak accidents. It is to design batteries on the assumption that individual cells can fail: detect trouble early, contain heat and gases, prevent propagation, improve crash protection, strengthen manufacturing oversight and make emergency response safer. The most convincing measure of progress will not be a claim that a battery can never fail. It will be evidence that when one cell does fail, the rest of the vehicle and the people around it remain protected.

Sources and further reading

Share This Article
Leave a Comment

Leave a Reply